Important Notice: Shielded CAT5e/CAT6 and shielded RJ45 connectors are strongly recommended for this product. Unshielded or improperly terminated cables may be susceptible to video dropout problems from ceiling fans and other EMI issues. Please note: for proper shielding, shielded connectors must be used with drains connected at both ends. In addition, “EZ end” connectors are not recommended for use with HDMI extenders.

Binary Cables
Binary™ Single Cat 5e/6  HDMI Extender (130') Plus IR Receiver & Flasher Pass Through

Additional Photos (click to enlarge):

Binary™ Single Cat 5e/6 HDMI Extender (130') Plus IR Receiver & Flasher Pass Through

Item#: B-200-1CAT-HDIR

Binary™ Single Cat 5e/6 HDMI® Extender Plus IR Receiver & Flasher Pass-Through (130 Ft.)
The Binary™ 1CAT HDMI Extender delivers reliable HDMI transmission up to 130’ over a single Cat5e/6 cable. This engineering marvel is able to transmit full HDMI 3D at 1080p with Deep Color and up to 7.1 channels of lossless audio – all without skipping a beat. And for the ultimate control system flexibility, it even carries bidirectional IR too!





Important Notice: To simplify installation, we have made a running design change to this product, effective on serial numbers higher than 71521209000. Power is no longer supplied to the transmitter’s IR input, meaning you don’t need to use the IR dongle when connecting it to a control system. Power is still supplied at the receiver’s IR input for quick connection of an IR receiver. More info

Important Notice: Binary 1 Cat HDMI extenders use a 5 Volt DC power supply. Binary HDBaseT extenders use a 24 Volt DC power supply, and matrix switchers with integrated Cat 5 extenders use 12 Volt DC supplies. Using any 12 or 24 Volt DC power supply with any 5 Volt Binary products will result in damage to the product and possibly the power supply. Be sure to use the correct power supply with the correct product!

HDMI® (3D) Compliant with Full 3D Support
This extender offers full support of HDMI® (with 3D), Deep Color (36bit) and HDCP 2.0 as well as support for Dolby® True HD, Dolby® Digital Plus, DTS™-HD Master and LPCM audio formats.

Bi-Directional IR
Over the same CAT5e cable, you can easily send commands from a control system to the TV – and simultaneously control DVD players, cable boxes and other source equipment from the TV location. For best performance, use Episode® IR flashers and receivers.

 


Engineered by SnapAV
Under the hood of the B-200-1CAT-HDIR is an engineer’s paradise! These surface-mount, high speed circuits are built on a multi-layer board to give you a solution that is specifically designed for custom install applications. "Engineered by SnapAV" – it’s not just a saying, it’s what we do.
 
Screw Down Power Plugs
Our In-line power supply has a screw lock to secure the power to the unit. No more worries about service calls just because the plug is loose or unplugged.
 
Built-In ESD and Surge Protection
Intelligent circuit design, perfected through extensive hardware testing, has resulted in a very robust product with excellent ESD and surge protection that exceeds CE Level 3 standards. During development, every connection was tortured with an ESD gun and a lightning simulator. They were hit with ESD at 15KV and surges up to 2500V. More important, though, they each lived to tell about it!

Easy Install
The durable low-profile metal cases come equipped with integrated mounting hardware for a variety of installation needs.


Product Contents
(1) Transmitter
(1) Receiver
(2) 5VDC in-line power adapters
(1) Manual
(8) rubber feet
(4) Mounting screws
(1) IR adapter cable

Still have a question?? Email us at support@snapav.com
 

Specifications
Technical
HDMI compliance HDMI 3D
HDCP Compliance Yes
Video bandwidth 6.75 Gbps
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over UTP Transmission 1080i/720p 24-bit color: 200 ft (cat5e), 200 ft (cat6)
Full HD 1080p 24-bit color: 130 ft (cat5e), 165 ft (cat6)
Full HD 1080p 36-bit color: 65 ft (cat5e), 65 ft (cat6)
Signal Equalization 8-level digital control at RX
Input TMDS Signal 12 Volts (peak-to-peak)
Input DDC Signal 5 Volts (peak-to-peak, TTL)
ESD Protection (1) Human body model — ±15kV (air-gap discharge) &
±8kV (contact discharge) (2) Core chipset — ±8kV
IR Signal (Bi-directional) Carrier frequency: 20-60KHz
Connections Transmitter Receiver
HD Link 1xRJ45 1xRJ45
HDMI 1xHDMI Type A (19 pin female) 1xHDMI Type A (19 pin female)
IR Receiver (In) 1x3.5mm Mono 1x3.5mm Stereo
IR Flasher (Out) 1x3.5mm Mono 1x3.5mm Mono
Power Latch-locking Latch-locking
Controls Transmitter Receiver
Rotary Control Switch EDID Mode Distance Signal level
Mechanical
Housing Metal Enclosure
Dimensions 1" (H) x 3.5" (W) x 2.9" (D)
Weight 1.1 lbs
Power Supply 5V DC 4A
Power consumption 3 watt (max)
Operation Temperature 32-104F
Storage temperature -4 - 140 F
Relative Humidity 20-90% RH (no condensation)

Manuals and Support Documents


Product Manual
IR Integration Application Guide
HDMI Best Practices Application Note
AutoCAD Drawing


 

Note:  This product was specifically engineered for Episode IRproducts.  Use of the following products is highly recommended (notincluded).



Episode® Electronics Single IR Flasher with LED Feedback
IRF-1
Episode® Electronics Surface-Mount Plasma-Proof IR Sensor with LED Feedback
IR-SM-3660


Warranty
2-Year Limited Warranty
This Binary product has a 2-Year Limited Warranty. The warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).