Your request is being processed. Loading...
{0} Hour(s)
{0} Day(s)
{0} Week(s)
{0} Month(s)
{0} Year(s)

more info

Click on more info to Add to order and more

BannerContent
Processing...

Episode® Electronics 2x6 IR Repeater with Power Supply - Kit

KIT-IR-RPTR-2
PDPRewardPointsEspot
Add to cart
Description
Support
FAQs
Description
Description

This kit works with most AV components and remote controls, providing plenty of flexibility for your two-zone, AV receiver-based systems. The repeater powers both IR sensors and repeats to up to 6 flashers - plus there's selectable routing for 2 of the IR flasher outputs. Small and rugged, this unit comes with steel mounting ears that have keyhole slots for quick, easy installation.

Episode® Electronics 2x6 IR Repeater with Power Supply

This kit works with most AV components and remote controls, providing plenty of flexibility for your two-zone, AV receiver-based systems. The repeater powers both IR sensors and repeats to up to 6 flashers - plus there's selectable routing for 2 of the IR flasher outputs. Small and rugged, this unit comes with steel mounting ears that have keyhole slots for quick, easy installation.

Support
ProductPageSupportTabEspot

Manuals and Guides

FAQs
FAQ

General

  • Using your IR2X6 connecting block with 2 identical sources, I am having an issue with both devices responding. What can I do to fix this?
    If the two devices are close to each other (e.g. stacked in a cabinet) use the supplied IR emitter blocking covers to prevent IR "bleed" from one component to another.
  • How do the A/B switches work?
    The IR2X6 can be configured to send IR from input “A” to all emitter outputs, or “B” to emitter outputs 5 and 6 by setting the switches located next to the emitter outputs (SW5, SW6) to “B”.
  • Can I connect more than one IR receiver to the screw terminals of the IR1X4 or 2X6 connecting block?
    You can parallel up to 4 IR receivers to the screw terminals of the IR connecting block.
  • My LED display seems to be interfering with the operation of your IR-receivers. What can I do to alleviate this issue?
    You can relocate the receiver away from the power supply of the display (usually a source of high EMI). If possible, try locating the receiver behind the face of the display (e.g. the wall or the face of a shelf). IR will usually reflect into the receiver just as effectively as if it were exposed.
  • I'm getting constant feedback (solid lights) on the IR receiver and have intermittent signal transfer issues (i.e.. changing channels/volume) with the IR receiver extended over Cat-5. Is there anything I can do to remedy this?
    Yes. First, try moving the IR receiver to a different area on the TV. It is also recommended to use the supplied 470 ohm resistor on the connecting block, bridged across signal and ground terminals.
  • Setup & Installation

  • How do I extend the wiring for IR repeaters?

    It is often necessary to extend the wiring of IR repeater systems so that it reaches between the controlled equipment and the source of the IR signals. You can use almost any type of multi-conductor wire that has the right conductors (at least 24 AWG), but we recommend using Cat5e/6 because it is common, will have more than enough conductors, and may have already been installed where you need it on retrofit jobs.

    IR Receiver or flasher wiring may be extended up to about 150 feet using this method. To extend a flasher signal, use one pair from the cable, splice the flasher head on one side and the male mono mini jack on the other, making sure not to change the wiring pattern from end to end. Use a pair for each conductor (plus and minus) if signal is not reliable.

    To extend IR receiver wiring, use use the wiring diagram illustrated below. Be sure to splice the same conductors in the same order at both ends.

    Cat5e/6All 4 Striped ConductorsGround/CommonIR
    Receiver
    Solid Blue and Solid Green
    Twisted Together
    IR Signal
    Solid Brown and Solid Orange
    Twisted Together
    +12V DC

3-Year Limited Warranty

This Episode® product has a 3-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).