Your request is being processed. Loading...
{0} Hour(s)
{0} Day(s)
{0} Week(s)
{0} Month(s)
{0} Year(s)

more info

Click on more info to Add to order and more

BannerContent
Processing...

Episode® Digital Subwoofer Amplifier w/ Front Panel Display | 500W x 1 Channel

EA-AMP-SUB-1D-500R-A
PDPRewardPointsEspot
Add to cart
Description
Specs
Support
FAQs
Description
Description

This digital subwoofer amplifier with front panel display and dual sub outputs runs steady at 500 Watts at 4 ohm, and is fine-tuned with custom EQ settings to be used with our dual 8" in-wall, 10” hardscape, or 12” burial subs.

Episode® Digital Subwoofer Amplifier - 500W with Front Panel Display

This digital subwoofer amplifier with front panel display and dual sub outputs runs steady at 500 Watts at 4 ohm, and is fine-tuned with custom EQ settings to be used with our dual 8" in-wall, 10” hardscape, or 12” burial subs.

Front Panel Display

This amp’s front panel screen displays the volume level and other control settings. Access the menu function screen using the selection knob to adjust volume, crossover, phase, and EQ settings. It also allows you to select sound mode, night mode, and power mode settings, and can assign an IR device ID for control system integration. Plus, there is a lock control setting that prevents accidental changes in settings.

Custom EQ Settings

This Episode® amplifier offers flexibility to enable or disable EQ settings. There are 3 custom EQ settings optimized for our subwoofers.

Power Mode Selection

Intelligent power management allows the amp to turn on automatically, either when an audio signal is detected or by using a 12V trigger from your AV receiver or processor. An illuminated front-mounted push button also allows you to turn the amplifier on or off when set to the always-on mode.

Connections

RCA line level inputs and pass-through outputs allow you to connect additional amplifiers, while the 12V trigger input and output allows you to connect another 12V trigger device; the amp also has dual sub outputs in parallel configuration.

Rackmount

Rackmount Installation Option

Rack ears with three fastening points help eliminate sag when the amp is installed into a rack, while top cover and side panel ventilation slots allow better airflow.

Control System Integration

Features an IR port to connect an IR device. Simply connect an IR repeater or IR controls system to the IR port on the back of the amplifier, and set the device ID in the front panel controls menu.

Subsonic Circuits

A limiter circuit has been incorporated into the amp to protect the connected subwoofer from harsh or damaging distortion that could not only ruin the listening experience, but the woofer

Specs
Specifications
EA-AMP-SUB-1D-500R
15.000 ohms
500W RMS
250W RMS
100 mV for 500W output 4 ohms
< 0.2%
"1.1 db at 300 Hz (Flat EQ, LFE Crossover Setting)
1.5 dB at 20 Hz"
2.6V
TUV listed
Tested under UL/EN60065 for US and Canada
16.9" x 1.75" x 8.1
8.5 lb
1U
88 dB (5 kHz bandwidth relative to 500W @ 4 ohms)
1-Channel
12V +/-1.2V no load
10.5 V with 100 mA load
 
Impedance Input
Power Output @ 4 ohm
Power Output @ 8 ohm
Sensitivity Input
Total Harmonic Distortion (THD)
Frequency Response
12V Trigger
Certifications
Dimensions (W x H x D)
Weight
Rack Spacing
Signal to Noise Ratio
Channels
External Trigger Voltage
Support
ProductPageSupportTabEspot
FAQs
FAQ

General

  • Is the front panel power button enabled when the amp is in TRIGGER or AUTO power modes?
    No, the front panel power button is only enabled when the power mode is set to ON.
  • Is there a user-serviceable fuse in my subwoofer amplifier?
    Yes, the EA-AMP-SUB-1D-500R is equipped with a replaceable fuse and is conveniently located inside the fuse tray of the unit. See the Owner’s manual for the location. If the fuse blows immediately, please contact Tech Support for help with troubleshooting or getting a replacement.
  • Is the 12V TRIGGER OUT active when any power mode (TRIGGER, AUTO, or ON) is selected?
    Yes, the 12V trigger out function is enabled in any power mode setting.

2-Year Limited Warranty

This Episode® Amplifier product has a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).